WELDING INSPECTION TECHNOLOGY WORKBOOK - MODULE 1

VT Test -  MODULE 1



QI-1 Why is there an increasing need for weld quality?
a. safety
b. economics
c. less conservative design
d. government regulations
e. all of the above

QI -2 What AWS document describes the rules for the CWI certification program?
a. AWS 5.5
b. AWS D1.l
d. AWS 5.1
e. AWS 14.1
C. AWS QC-1

QI-3 Weld quality control should begin after welding has been initiated.
a. true
b. false

Q I 4 What are the three welding inspector certifications covered in AWS QC-i?
a. CAWI, CWI, BWI
b. CWI, CAWI, SCWI
c. SCWI, CWI, ACWI
d. Level I, II, and III
e. None of the above

Q1-5 What is generally considered to be the most important quality of a welding inspector?
a. graduation from a welding vocational program
b. an engineering degree
c. an associate degree
d. professional attitude
e. hold a certified welder certificate

QI-6 The vision requirements for a CWI are near vision acuity on:

a. Jaeger J1 at 24 inches
b. Jaeger 52 at 12 inches
c. Jaeger 52 at 12 inches, with or without corrective lenses
d. the inspector cannot wear glasses
e. 20/20 vision

QI-7 The acronym KASH stands for:

a. knowledge, attitude, skills, and habits
b. knowledge, application, skills, and habits
c. knowledge, attitude, skills, and honesty
d. knowledge, application, skills, and honesty
e. knowledge, attitude, sincerity, and honesty

Q1-8 The welding inspector should have a basic understanding of


a. welding processes
b. nondestructive testing methods
c. a and b above
d. codes and standards
e. all of the above

Q1-9 The term used to describe a delay in the production schedule to permit inspection is:

a. NDE
b. hold point
c. pre-inspection
d. reference point
e. arc strike

Q1-1 O Inspection report corrections should be made by:

a. rewriting the entire report
b. reporting the correction to the welding foreman
c. telling the welder what was done
d. ignoring the original error
e. single-line out the error, correct the error, date, and initial

Q1-11 A definition of ethics is:

a. using common sense and honesty
b. living by the rules
c. being fair and impartial
d. basing decisions on facts
e. all of the above

Q1-12 For communications to be effective, it should form a “continuous loop.”

a. true
b. false

Q1-13 The welding inspector must often communicate with:

a. welders
b. supervisors
c. welding engineers
d. members of management
e. all of the above

Q1-14 NDE personnel (other than CWI’s) should be certified to what document?

a. QC-1
b. D1.1
c. API 1104
d. ASNT SNT-TC-1A
e. certification is not needed


QI-I5 You must have a high school diploma to become a CWI.

a. true
b. false

QI-I6 The CWI exam has several parts; these are:

a. fundamentals, practical, code
b. fundamentals, basic, code
c. basic, vision test, fundamental
d. code, vision test, practical
e. none of the above

QI-17 The CWI exam requires that the D1.l Code be used for the open book Code test.

a. true
b. false

QI-I8 The CWI exam contains three parts, each two hours long.

a. true
b. false

QI-I9 The title of the AWS Standard, A3.0 is:

a. Filler Metal Specifications
b. Standard Welding Terms and Definitions
c. Guide to CWI Certificatioin
d. Requirements for CWI Certification
e. none of the above

QI-20 API Standard 1104 covers the fabrication of cross-country bridges.

a. true
b. false

QI-21 Some of the approved codes/standards for the open book portion of the CWI exam are AWS
D1.l, API 1104, AWS D1.5, and AWS D15.1.

a. true
b. false

Ql-22 Prior to starting a job assignment, the welding inspector should determine:

a. what code, standard, or specification applies
b. what inspections should be conducted
c. when inspections should be conducted
d. where records are maintained
e, all of the above