WELDING INSPECTION TECHNOLOGY WORKBOOK - MODULE 5
VT Test - MODULE 5
Q5-7 Of the following types of documents, which have general acceptance in the welding industry?
a. contracts
b. standards
c. specifications
d. drawings
e. all of the above
Q5-8 The code that covers the welding of steel structures is:
a. ASME Section IX
b. ASMEB31.1
c. API 1104
d. AWS D1.l
e. ASMEB31.3
Q5-9 The code that covers the design of metallic unfired pressure vessels is:
a. ASME Section XI
b. ASME Section VI11
c. ASME Section X
d. API 1104
e. AWS D1.1
Q5-1O The series of specifications covering the requirements for welding electrodes is designated:
a. AWSD1.X
b. AWS D14.X
d. ASTMA53
e. ASTMA36
C. AWS A5.1-A5.31
Q5-11 Which of the following methods for controlling materials in a fabrication shop is most suitable
for automation?
a. color coding
b. alpha-numeric coding
c. heat number transfer
d. bar coding
e. segregation by alloy
Q5-12 Which Section of the ASME Code covers qualification of welders?
a. Section V
b. Section XI
c. Section III
d. Section VI11
e. Section IX
Q5-13 Tolerances are required on drawings to:
a. guide the inspector on permissible size variations
b. show the total amount of variation permitted from the design size
c. both a and b above
d. none of the above
Q5-14 Tolerances can be expressed:
a. as a variation between limits
b. as plus or minus dimension
c. as a design size with either a plus or a minus
d. all of the above
e. none of the above
Q5-15 Drawing notes can be classified as:
a. general
b. local
c. specifications
d. ali of the above
e. none of the above
Q5-16 Hold points refer to:
a. the points for lifting an object
b. a delay in fabrication to permit inspection
c. a shutdown at the end of the day
d. none of the above
Q5-17 The welding inspector is not responsible for checking to make sure all welding and testing
personnel have adequate certifications.
a. true
b. false
Q5-18 The American Welding Society has developed how many welding codes?
a. one
b. two
c. three
d. four
e. six
Q5-19 When inspecting unfired pressure vessels to the ASME Code, the inspector will usually use
several different Sections.
a. true
b. false
Q5-20 In what Section of the ASME Code are the filler materials found?
a. Section III
b. Section II, Part C
c. Section II, Part D
d. Section IX
e. none of the above
Q5-21 Standards are never considered mandatory.
a. true
b. false
Q5-22 Base metals used in fabrication can be bought to conform with which of the following?
a. ASTM Standards
b. ASME Code, Section II, Parts A and B
c. it is not required to specify base metals
d. a and b above
e. none of the above
Q5-23 The AWS Specifications designated as A5.XX refer to:
a. filler metals
b. rules for bridges
c. cross country pipelines
d. pressure vessel fabrication
e. none of the above
Q5-24 An effective materials control system will:
a. be as simple as possible
b. contain checks and balances
c. not be necessary unless the fabrication is for nuclear work
d. be based on “first in - first out"
e. a and b above
Q5-25 UNS refers to:
a. United Nondestructive Society
b. United National Standards
c. Unified National System
d. Unified Numbering System
e. none of the above
Q5-26 Who is normally responsible for the qualification of welding procedures and welders?
a. welder
b. architect
c. welder’s employer
d. engineer
e. Code body
Q5-27 Which of the following processes is not considered prequalified in accordance with AWS D1.1?
a. shielded metal arc
b. submerged arc
c. short-circuiting transfer gas metal arc
d. spray transfer gas metal arc
e. flux cored arc
Q5-28 Of the following types of test specimens, which is used by API and not ASME for procedure and
welder qualification testing?
a. face bend
b. root bend
c. side bend
d. nick break
e. tensile
Q5-29 What is the pipe welding position where the pipe remains fixed with its axis horizontal, so the
welder must weld around the joint?
a. 1G
b. 2G
c. 5G
d. 6G
e. 6GR
Q5-30 What is the pipe welding position where the axis of the pipe lies fixed at a 45-degree angle?
a. 1G
b. 2G
c. 5G
d. 6G
e. none of the above
Q5-31 What is the pipe position test for welders who are trying to qualify to weld T, K, andY connections?
a. 1G
b. 2G
c. 5G
d. 6G
e. 6GR
Q5-32 If a welder qualifies to weld with an E6010 electrode, which is an F3 group electrode, he is also
qualified to weld with all of the following except:
a. E6011
b. E6012
c. E7018
d. E7024
e. E6013
Q5-33 With relation to procedure and welder qualification, which of the following can be an important
task for the welding inspector?
a. watching the welding qualification test
b. identifying samples
c. cutting and testing specimens
d. monitoring production welding
e. all of the above
Q5-34 For most codes, if a welder continues to use a particular process and procedure, how long does
the welder’s qualification remain in effect?
a. indefinitely
b. 6 months
c. 1 year
d. 3 years
e. until the welder produces a rejectable weld
Q5-1 Which of the following do not contain job quality requirements?
a. codes
b. drawings
c. specifications
d. textbooks
e. Standards
Q5-2 Of the following, which may be considered mandatory?
a. codes
b. specifications
c. standards
d. all of the above
e. none of the above
Q5-3 The job documents that best describe the size and configuration of a weldment are:
a. codes
b. standards
c. specifications
d. drawings
e. none of the above
Q5-4 The type of document that has legal status by definition is:
a. code
b. standard
c. specification
d. both a and b above
e. all of the above
Q5-5 The type of document that describes the requirements for a particular material or component is
referred to as:
a. code
b. standard
c. specification
d. a and b above
e. b and c above
Q5-6 Something set up and established by authority as a rule to measure quantity, quality, value, or
weight is a:
a. specification
b. standard
c. code
d. drawing
e. none of the above
Q5-7 Of the following types of documents, which have general acceptance in the welding industry?
a. contracts
b. standards
c. specifications
d. drawings
e. all of the above
Q5-8 The code that covers the welding of steel structures is:
a. ASME Section IX
b. ASMEB31.1
c. API 1104
d. AWS D1.l
e. ASMEB31.3
Q5-9 The code that covers the design of metallic unfired pressure vessels is:
a. ASME Section XI
b. ASME Section VI11
c. ASME Section X
d. API 1104
e. AWS D1.1
Q5-1O The series of specifications covering the requirements for welding electrodes is designated:
a. AWSD1.X
b. AWS D14.X
d. ASTMA53
e. ASTMA36
C. AWS A5.1-A5.31
Q5-11 Which of the following methods for controlling materials in a fabrication shop is most suitable
for automation?
a. color coding
b. alpha-numeric coding
c. heat number transfer
d. bar coding
e. segregation by alloy
Q5-12 Which Section of the ASME Code covers qualification of welders?
a. Section V
b. Section XI
c. Section III
d. Section VI11
e. Section IX
Q5-13 Tolerances are required on drawings to:
a. guide the inspector on permissible size variations
b. show the total amount of variation permitted from the design size
c. both a and b above
d. none of the above
Q5-14 Tolerances can be expressed:
a. as a variation between limits
b. as plus or minus dimension
c. as a design size with either a plus or a minus
d. all of the above
e. none of the above
Q5-15 Drawing notes can be classified as:
a. general
b. local
c. specifications
d. ali of the above
e. none of the above
Q5-16 Hold points refer to:
a. the points for lifting an object
b. a delay in fabrication to permit inspection
c. a shutdown at the end of the day
d. none of the above
Q5-17 The welding inspector is not responsible for checking to make sure all welding and testing
personnel have adequate certifications.
a. true
b. false
Q5-18 The American Welding Society has developed how many welding codes?
a. one
b. two
c. three
d. four
e. six
Q5-19 When inspecting unfired pressure vessels to the ASME Code, the inspector will usually use
several different Sections.
a. true
b. false
Q5-20 In what Section of the ASME Code are the filler materials found?
a. Section III
b. Section II, Part C
c. Section II, Part D
d. Section IX
e. none of the above
Q5-21 Standards are never considered mandatory.
a. true
b. false
Q5-22 Base metals used in fabrication can be bought to conform with which of the following?
a. ASTM Standards
b. ASME Code, Section II, Parts A and B
c. it is not required to specify base metals
d. a and b above
e. none of the above
Q5-23 The AWS Specifications designated as A5.XX refer to:
a. filler metals
b. rules for bridges
c. cross country pipelines
d. pressure vessel fabrication
e. none of the above
Q5-24 An effective materials control system will:
a. be as simple as possible
b. contain checks and balances
c. not be necessary unless the fabrication is for nuclear work
d. be based on “first in - first out"
e. a and b above
Q5-25 UNS refers to:
a. United Nondestructive Society
b. United National Standards
c. Unified National System
d. Unified Numbering System
e. none of the above
Q5-26 Who is normally responsible for the qualification of welding procedures and welders?
a. welder
b. architect
c. welder’s employer
d. engineer
e. Code body
Q5-27 Which of the following processes is not considered prequalified in accordance with AWS D1.1?
a. shielded metal arc
b. submerged arc
c. short-circuiting transfer gas metal arc
d. spray transfer gas metal arc
e. flux cored arc
Q5-28 Of the following types of test specimens, which is used by API and not ASME for procedure and
welder qualification testing?
a. face bend
b. root bend
c. side bend
d. nick break
e. tensile
Q5-29 What is the pipe welding position where the pipe remains fixed with its axis horizontal, so the
welder must weld around the joint?
a. 1G
b. 2G
c. 5G
d. 6G
e. 6GR
Q5-30 What is the pipe welding position where the axis of the pipe lies fixed at a 45-degree angle?
a. 1G
b. 2G
c. 5G
d. 6G
e. none of the above
Q5-31 What is the pipe position test for welders who are trying to qualify to weld T, K, andY connections?
a. 1G
b. 2G
c. 5G
d. 6G
e. 6GR
Q5-32 If a welder qualifies to weld with an E6010 electrode, which is an F3 group electrode, he is also
qualified to weld with all of the following except:
a. E6011
b. E6012
c. E7018
d. E7024
e. E6013
Q5-33 With relation to procedure and welder qualification, which of the following can be an important
task for the welding inspector?
a. watching the welding qualification test
b. identifying samples
c. cutting and testing specimens
d. monitoring production welding
e. all of the above
Q5-34 For most codes, if a welder continues to use a particular process and procedure, how long does
the welder’s qualification remain in effect?
a. indefinitely
b. 6 months
c. 1 year
d. 3 years
e. until the welder produces a rejectable weld
Comments
Post a Comment