links

WELDING INSPECTION TECHNOLOGY WORKBOOK - MODULE 9

VT Test -  MODULE 9



Q9-1 A discontinuity is: 


a. always a defect
b. always a reject
c. always acceptable
d. rejectable if it exceeds code limits
e. none of the above

Q9-2 Whether a particular weld discontinuity is critical can be judged on the basis of


a. whether it is surface or subsurface.
b. whether it is linear or nonlinear.
c. whether it has a sharp end condition.
d. all of the above
e. none of the above

Q9-3 What discontinuity is generally considered to be the most severe?


a. porosity
b. incomplete fusion
c. slag inclusion
d. crack
e. arc strike


Q9-4 Which of the following discontinuities is less likely to be found visually?


a. toe crack
b. undercut
c. lamellar tear
d. overlap
e. none of the above

Q9-5 Underbead cracks can result from which of the following welding practices?


a. use of wet electrodes
b. welding on contaminated steels
c. welding over paint
d. all of the above
e. none of the above


Q9-6 The weld discontinuity that results from improper termination of the welding arc is referred to as:


a. undercut
b. overlap
c. crater crack
d. incomplete fusion
e. all of the above



Q9-7 Of the following processes, which is unlikely to have slag inclusions in a completed weld?

a. SMAW
b. PAW
c. FCAW
d. SAW
e. none of the above

Q9-8 The discontinuity that results from the entrapment of gas within the weld cross section is
referred to as:

a. crack
b. slag inclusion
c. incomplete fusion
d. porosity
e. none of the above

Q9-9 What weld discontinuity results when the welder travels too slowly, causing excess weld metal to flow out of the joint and lay on the base metal surface without fusing?

a. undercut
b. underfill
c. overlap
d. incomplete fusion
e. none of the above

Q9-1O What weld metal discontinuity results when the welder fails to completely fill the weld groove?

a. underfill
b. undercut
c. overlap
d. incomplete fusion
e. none of the above

Q9-11 Excessive weld metal buildup on a groove weld is referred to as:

a. excess convexity
b. excess weld reinforcement
c. overfill
d. all of the above
e. none of the above

Q9-12 The weld discontinuity that results from the initiation of the welding arc outside the weld joint is referred to as:

a. incomplete fusion
b. undercut
c. overlap
d. scratch start
e. arc strike


Q9-13 What weld discontinuity shows up as a light region on a radiograph?


a. porosity
b. tungsten inclusion
c. slag inclusion
d. a and b above
e. b and c above


Q9-14 Which of the following is not a base metal discontinuity resulting from improper steelmaking
practices?


a. lamination
b. lamellar tear
c. seam
d. pipe shrinkage
e. none of the above


Questions Q9-15 through Q9-19 refer to the figure shown below:



Q9-15 What discontinuity is shown by #12b?

a. longitudinal crack
b. transverse crack
c. underbead crack
d. toe crack
e. root crack

Q9-16 What step-like discontinuity is shown by #11?

a. lamination
b. porosity
c. lamellar tear
d. seam
e. lap

Q9-17 What discontinuity is shown by #12g?

a. toe crack
b incomplete fusion
c. root crack
d. lamellar tear
e. underbead crack

Q9-18 What discontinuity is shown by #5?

a. undercut
b. underfill
c. overlap
d. incomplete fusion
e. toe crack

Q9-19 What discontinuity is shown by #lo?

a. lamination
b. seam
c. delamination
d. base metal crack
e. incomplete fusion








Comments

Post a Comment

Ads

Popular posts from this blog

Penetrant Testing (PT)

Image
Penetrant Testing (PT) In general terms, penetrant testing reveals surface discontinuities by the bleedout of a penetrating medium against a contrasting colored background. This is accomplished by applying a penetrant (usually liquid) to the cleaned surface of the test piece. Once this penetrant is allowed to remain on the surface for a prescribed time (dwell time), it will be drawn into any surface opening by capillary action. Subsequent removal of excess penetrant and application of a developer draws remaining penetrant from discontinuities.  The resultant indications are shown in high contrast and magnify the presence of the discontinuity so it can be visually interpreted. There are two primary ways in which penetrant materials are grouped: specifically, the type of indication produced, and the method of excess penetrant removal.  The two penetrant indications are visible and fluorescent.  The visible dye (usually red) produces a vivid red indication against
Read more

Magnetic Particle Testing (MT)

Image
Magnetic Particle Testing (MT) This particular nondestructive test method is used primarily to discover surface discontinuities in ferromagnetic materials.  While indications can be observed from subsurface discontinuities very near the surface, they are very difficult to interpret, and often require testing by other methods.  Other NDE techniques are usually required for subsurface discontinuity detection and interpretation.  However, surface discontinuities present in a magnetized part will cause the applied magnetic field to create “poles” of opposite sign on either side of the discontinuity, creating a very attractive force for iron particles.  If iron particles, which are “magnetic particles” since they can become magnetized, are spnnkled on this surface, they will be held in place by this attractive field to produce an accumulation of iron particles and a visual indication of the discontinuity. While several different types of magnetic particle tests exist, th
Read more

Nondestructive Testing (NDT)

Nondestructive Testing (NDT) One of the purposes of an effective quality control program is to determine the suitability of a given base metal or a weld to perform its intended service. One way to judge that suitability is to subject the base metal or weld to destructive tests which would provide information about the performance of that test object. The major disadvantage of such an approach is that, as the name implies, the test object is destroyed in the process. Therefore, a number of tests have been developed to provide an indication of the acceptability of the test object without rendering it unusable for service. These various tests are referred to as nandestructìve tests, because they permit the nondestructive evaluation (NDE) of the metal or component. Even the destructive testing of a given percentage of parts can be expensive and assumes that the untested parts are of the same quality as those tested. Nondestructive tests yield indirect, yet still valid, results
Read more